DIY Concrete Lamp

And the award for the Most Fun project of the Year goes to… DIY concrete lamps!

Pin

How to make a DIY cement lamp

Today I’m sharing how so you can make your own cement, concrete or stone lamp in two different styles—no DIY or artistic skills required (really!)

Pin

Materials:

• Lamp base and lamp shade (I found mine at a thrift store and Walmart)
• Ready-mix concrete patch
• Spackle
• Spray primer
• Paint (any kind will work—I used shades of white, brown and black)

Tools:

• Putty knife
• Coarse sanding block
• Paint brush
• Gloves
• Optional: wire brush

Here was my inspiration—I’m sure you’ve all seen these beautiful but very pricey lamps all over your favorite designers Instagram accounts…

Pin

Pin

Pin

Pin

There are a multitude of ways to achieve this aged stone/concrete look, and I’ve experimented with a few myself (see DIY Hypertufa planter, DIY aged stone planters). This time around, I wanted to try something new and foolproof for complete beginners. This technique I found might be my favorite so far, requires only a few basic ingredients and anyone can get awesome results!

Step 1: Find an old lamp (or any vessel)

Preferably something used/inexpensive. I found mine at Walmart and a thrift store—Facebook Marketplace is another good place to look. There are no shortage of these lamps out there!

Pin

Choose something with a rounded/jug shape—if it has handles, even better. The material doesn’t matter. My thrifted lamp had a gap along the bottom, so I decided to fill it in by shoving painters tape into the crevice and using a hot glue gun to attach a ribbon around it. It was all I could think of at the moment but it worked just fine!

Pin

Step 2: Prime

First, mask the socket base and cord with painter’s tape. You’ll first want to coat the lamps with a oil based spray primer to de-slick the surface so the concrete patch has the best chance of sticking. This is the stuff I swear by for anything non-wood—it dries almost instantly and covers very well.

Pin

Step 3: Apply concrete patch

Now it’s time for the fun part!

Pin

Using a putty knife, apply a layer of concrete patch (found at Lowe’s or Home Depot) to the entire surface. You can make it as thick or as thin as you’d like, and don’t worry about making it even and smooth at this point.

Pin

I found that the putty knife spread the concrete mixture quite well—just make sure that the concrete patch is fresh and not dried out.

Pin

Once the lamp is covered, you may notice that it is already starting to dry and set. When I tried smoothing the edges with the putty knife, the pressure made the concrete patch start to rub off in some areas, so I came up with a different approach: use a stiff paint brush to stipple the surface and even everything out.

Pin

This not only blended in the lines, but it gave it a nice rough texture that looked more like concrete/stone. Definitely don’t skip this step!

Pin

Pin

Allow to the lamp to fully cure for at least a few hours. You can also add a second coat if you think it needs more.

Pin

Step 4: Apply joint compound

At first I thought this could be an optional step, but now I’m convinced it’s necessary—and it’s a fun step!

Pin

I used this spackling, but literally any kind will work.

Pin

This is also best applied with a putty knife, and the idea is to apply it to random areas (not the entire surface).

Pin

Unlike the concrete patch, joint compound will dry smooth which creates a nice variation in texture.

Pin

I applied a lighter coat on the second lamp to see if it made any difference, and I don’t think it was noticeable either way in the end.

Pin

If you’re going for a natural gray cement lamp, I’d go a little lighter on the spackling so that more of the gray can show through.

Step 5: Sand

Once the joint compound is dry (mine was dry in an hour or so) it’s time for the easiest part—sanding! A sanding sponge is the easiest way to do this, and it only takes a minute to go over it just enough to blend it in.

Pin

One tool I had forgotten and wish I would have used before the concrete patch dried is a coarse wire brush. This will really roughen up the surface and add texture that makes it look authentically worn (it’s also my secret to aging wood!)

Pin

I used it to scratch up the surface as best as I could after the spackle dried, but it would have been even more effective to use before the concrete patch had dried. Not 100% necessary, but it adds a little extra something!

Step 6: Paint

This is where things really start to take shape. For the gray concrete lamp, I mixed up a muddy beige color from old paint samples and brushed on a thin layer.

Pin

You want to keep it light so that the white and gray underneath shows through. In hindsight I wish I would have done a slightly thinner coat.

Pin

The first muddy beige color I applied ended up drying more gray than I wanted, so I went over it again with a true beige. The goal is to add as much variation and layers (of both color and texture) as possible—and anything pure gray will dry too blue, so use warmer tones!

Pin

For the black lamp, I wanted a dimensional look, so I mixed up a rusty brown color with random paints (any type of paint will work here).

Pin

Pin

The fun thing about this project is that there’s no right or wrong. Use any colors you want, and as much or as little as you want!

Pin

Once the brown paint dried, I gave it a light coat of black—still allowing some of the brown, white and gray to show through.

Pin

Two different looks, same technique:

Pin

Step 7: Sand

Almost done! Now we put the finishing touches on our creations by sanding to reveal the layers underneath.

Pin

To keep more of the color you can give it a light sanding, or continue sanding to make it more distressed. Anything goes!

Pin

Pin

For the gray concrete lamp, I sanded and went over it with a wire brush which gave the unintended but interesting result of burnishing the surface to make it darker.

Pin

As a final step on this lamp, I dipped my brush in black paint and flicked the bristles to add tiny splatter dots.

Pin

I repeated this with white and beige paint, and love the effect! It makes it look porous like real concrete/stone.

Pin

And here they are… just screw a light bulb in, pop a lamp shade on and you’re done!

Pin

I think you could put them in a lineup with those $340 lamps and no one would ever know.

Pin

Do you have a favorite?

Pin

You don’t have to choose—you can make both! And maybe even 50 more for the price of one of those real stone lamps 😉

Pin

Honestly, I had so much fun making these that I’d actually pay to spend a weekend making them again. It’s a legitimate hobby.

Pin

Who wants to get together and have a lamp glow-up party?

Pin

Or maybe I should just retire from blogging and make these all day. Hah!

Pin

There are still more aged pottery/stone techniques I want to try out (and I’ll share those results with you when I do!) but I’m definitely adding this one to my DIY arsenal. Have you tried a similar project?

Pin

If you like this project, check out these similar beginner DIYs from my Project Library!

• Faux stone planters
• DIY Hypertufa ‘Stone’ Planter
• How to realistically age wood (the easy way!)
• How to make anything ‘antique’ brass

Pin